Driveway Restoration in Keynsham

Driveway restoration cost depends on the surface type (block paving, tarmac, resin, patio), the size of the area, the severity of staining, whether the jointing needs fully replacing, and the sealer specification. Every job is individually quoted after a free site visit — we give you a fixed written price before any work starts, with no obligation to proceed.

In most cases restoration is genuinely worth it — a proper clean, re-joint and seal costs a fraction of a new driveway and lasts 10+ more years. Replacement is only the right call when the sub-base has failed, blocks are cracked or sinking across large areas, the surface is structurally compromised, or the drainage is fundamentally broken. We'll tell you honestly at the survey which route is right for your driveway. We won't push restoration if it can't deliver.

We use a three-stage process: (1) a targeted chemical pre-treatment matched to the contamination — biocides for moss and algae, degreasers for oil, acid-based cleaners for calcium deposits and ingrained dirt; (2) hot-water pressure washing up to 3,000 PSI with a rotary surface cleaner (often called a whirlaway) — this gives a stripe-free finish without gouging the blocks; (3) a full joint re-sanding with either kiln-dried sand or polymeric jointing compound to lock the blocks back in place and prevent weed regrowth.

Yes — but only where they add value and always with care. We use professional-grade products: sodium hypochlorite-based biocides to kill moss, algae and lichen at the root; alkaline degreasers for oil and diesel stains; acid-based deposit removers (typically brick and patio cleaners at a controlled dilution) for ingrained dirt and calcium scale; and specialist rust removers for iron staining. All chemicals are used at manufacturer-recommended dilutions, rinsed thoroughly, and collected or neutralised to avoid drainage contamination. Surrounding planting is protected throughout.

It depends on the surface. For block paving we typically use a solvent-based acrylic sealer for a natural or wet-look finish, or a water-based version where fumes are a concern. For natural stone and sandstone patios we use a breathable impregnating sealer that protects without sitting on the surface. For resin driveways we use a UV-stable polyurethane top-coat matched to the original resin system. For tarmac we use a bitumen-based rejuvenating seal that refreshes the colour and re-binds the surface. We carry sample panels so you can see the finish before committing.

Yes — resin restoration is one of our growing specialisms. The process depends on condition. Worn patches or areas where the resin has failed are cut back to a clean edge, primed, and re-laid with matching aggregate blended to colour-match the existing surface. Surface fading is addressed with a fresh UV-stable polyurethane top-coat. Loose stones are re-bonded or, where necessary, small areas are fully re-laid. Resin driveways are generally restorable up to 10–15 years old depending on the original system.

Yes. Tarmac restoration typically involves three stages: crack sealing with hot-applied bitumen rubber, patch repair of potholes or broken edges using cold-lay or hot-lay asphalt, and a final bitumen-based rejuvenating seal that refreshes the colour back to deep black and re-binds the surface aggregate. A tarmac driveway that looks grey and tired can be brought back to near-new appearance in a single day for most domestic sizes.

Polymeric jointing compound is a resin-and-sand mix — common brands are GeoFix, EasyJoint and Rompox-D1 — that's brushed into the joints between block paving or patio slabs and then activated with a fine water spray. Once set it becomes a solid, flexible joint that resists weed growth, stops sand washing out in heavy rain, and locks the blocks in place. It's the single biggest upgrade a block paving driveway can have during restoration — typically 5+ years of weed-free joints.

Most domestic driveway restorations take 1–2 days. Day 1 is typically chemical pre-treatment, hot pressure wash and full dry-down. Day 2 is joint replacement (sand or polymeric compound), sealer application and site clean-down. Larger driveways or those needing significant patch repair may take 3 days. We give you a firm timescale with your fixed written quote.

For block paving sealed with an acrylic sealer, we recommend resealing every 3–5 years depending on traffic volume and sun exposure. For resin driveways with a UV-stable top-coat, 5–7 years is typical. For tarmac, a fresh rejuvenating seal every 5–6 years keeps the surface black and protected. A driveway that was restored and sealed 5+ years ago is the perfect candidate for another wash-and-seal — it rarely needs the full restoration process again.

No — not when used correctly. We pre-wet surrounding planting before any chemical application, contain overspray with sheeting where needed, and thoroughly rinse all treated surfaces. We also match the chemical strength to the job — no stronger than needed — and time applications to avoid heavy rain washing product into drainage. 20+ years of doing this and we've never damaged a client's garden. It's part of why people hire a professional rather than buying supermarket driveway cleaner.

Yes — patio regrouting is one of the most transformative restoration jobs we do. Old, cracked, weedy jointing is raked out to a consistent depth. The surface is pressure washed. Fresh polymeric jointing compound — matched to the patio colour — is brushed into every joint and activated with water. Or for natural stone patios where appearance matters more, we hand-point with a colour-matched mortar. The result is a patio that looks like it was laid last month.